Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Dover, TN to inspect, repair, and replace with zero guesswork.
We didn't start Forge Siding to push volume — we built it because homeowners in Dover kept getting burned by crews who cut corners on material selection, skipped moisture barriers, and left job sites messy. That's not how we work. Every Siding project starts with an honest assessment: we look at your substrate condition, check for existing rot or moisture intrusion, and talk through your options before a single nail goes in.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Paint peeling on your inside walls near exterior surfaces is a classic sign that moisture is migrating inward through failing siding. By the time you see it inside, the wall cavity is already compromised.
Panels that have pulled away from the wall are an open door for pests, moisture, and cold air. Nails back out over time when the substrate is soft — often a sign of prior water damage underneath.
Old or failing siding, particularly if the housewrap underneath has deteriorated, acts like a thermal short-circuit. Your HVAC runs harder to compensate, and the bills reflect it before the siding looks obviously bad.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
From a single damaged panel to a complete re-side on a large commercial property, we handle the full range of exterior cladding work — and we do it with the same crew standards regardless of job size.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for TN's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
LP SmartSide and similar engineered wood products split the difference between the look of real wood and the dimensional stability of manufactured products. They're primed at the factory, accept field-applied paint well, and hold up to impact and moisture better than OSB or solid wood. We use LP SmartSide Trim & Fascia alongside the panel and lap systems so the trim package matches — no mixing incompatible products that age differently.
Not every siding problem needs a full re-side. Storm impact, vandalism, or isolated rot can often be addressed with a targeted repair that blends into the existing field. We stock common profiles and can often source discontinued patterns through our supplier network for historic or older homes where matching matters. Partial replacement work is priced honestly — if we see a repair scope that's going to creep, we say so before we start, not after.
Commercial and multi-unit projects have different demands — larger panel formats, longer exposure to foot traffic and equipment contact, stricter fire ratings in some occupancy classes, and coordinated scheduling with other trades. Forge Siding handles commercial cladding projects in Dover, TN with full project management: dedicated site supervisor, daily progress reporting, and material delivery coordinated to minimize storage and laydown area on constrained sites.
Soffit ventilation is often compromised during re-siding work when installers don't maintain existing vent openings or fail to add ventilation where it was previously missing. We verify soffit net-free vent area against attic square footage before closing up the overhang — because your roofing contractor will find the problem later if we don't.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
We schedule your project start date at contract signing and stick to it. Materials are delivered directly to the site before crew arrival — no day-of scrambling. We protect landscaping, windows, and any surfaces adjacent to the work area before the first panel comes off.
Installation follows manufacturer specs and local building code. When work is complete, the lead installer does a quality check before calling you for the final walkthrough. You inspect every elevation — we go through it with you, address anything that needs attention, and make sure the site is clean and restored before we invoice.
Every crew that works on your home carries a current contractor's license for TN, full general liability, and workers' compensation. We'll email you the certificates before we arrive — not after you ask three times.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Dover, TN on the fact that our estimates are reliable.
We run our calendar tightly so the start date we give you is the date we're there. If a legitimate delay comes up — major weather, material shortage — we call you the day before and reschedule immediately, not a week later.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Get the Details on Our Warranty — +1-844-782-0929Straight from the homeowners we've worked with across Dover and Dover, TN.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
I manage a twelve-unit building in Dover and we needed LP SmartSide on three facades before winter. Forge Siding coordinated with our property manager, worked around tenant schedules, delivered materials in two staged drops to keep the lot clear, and finished four days ahead of the original schedule. Commercial billing was clean and documented. They're on our preferred vendor list now.
We went with insulated vinyl — Forge Siding recommended the insulated backer for our exposure and the energy savings have been real. First heating season after the install, our gas bill dropped noticeably. Installation crew was professional, on time every day, and the lead installer walked me through every elevation before he called the project done.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
I'm a home inspector by trade, so I know what cutting corners on a siding installation actually looks like behind the panels. Forge Siding's work is correct — right fastener pattern, proper clearances from grade and roofline, continuous housewrap with taped seams at all penetrations. This is how it's supposed to be done and most of the crews I see in Dover, TN don't do it this way.
I needed a quick turnaround on a rental property before a new tenant moved in. Forge Siding fit us in on short notice, did a clean vinyl replacement on two elevations, and the inspection cleared without a single callback item. Responsive, professional, priced fairly. That's all I ask for and they delivered all three.
We get these questions every week. Here are the honest answers.
We're not a national call center subcontracting your project to whoever's available. Our crews are based in and around Dover, TN. We know local code requirements, local supplier lead times, and local weather patterns — and that local knowledge shows up in how the project runs.
Our primary service area covers Dover and surrounding communities within our regional radius. Call +1-844-782-0929 to confirm service availability at your address — we'll tell you same-day.
Don't let failing siding go another season. Call Forge Siding and we'll have an estimator out to your property within 24 hours.
Schedule My Assessment — +1-844-782-0929